Duaer

Guides

How to Build a Process Knowledge Graph in 2027: Three Data Types Manufacturers Should Govern First

Drawn from the Duaer documentation site, this guide explains why process knowledge is scattered across manufacturing systems, common pitfalls in process knowledge graph construction, and a practical approach: define a narrow scope, design the ontology first, align data, and validate with domain experts.

Where Process Knowledge Lives and Why It Is Hard to Graph

Many manufacturers face a similar situation: they do not lack process knowledge, but they lack knowledge that systems can actually use. Process parameters sit in route cards, troubleshooting experience stays in the heads of senior technicians, defect records are buried in the remarks column of quality logs, and equipment alarms live in PLCs or historian databases. When a new engineer asks why a certain defect keeps appearing in summer, no one can connect these pieces of information within five minutes.

This is exactly the problem a process knowledge graph is meant to solve. It makes the relationships between operations, parameters, equipment, materials, defects, and standard documents explicit, so that questions such as which parameter affects which defect, on which machine it has appeared, and how it should be handled under which standard can be queried, reasoned over, and reused. A graph, however, is not just a technical label. It is a business asset that needs continuous maintenance. The sections below walk through the most common pitfalls and more reliable practices in the order you would actually work.

The difficulty is not primarily technical. Process knowledge has three natural characteristics. First, terminology is inconsistent: the same operation may be called 'reflow soldering' in the route card, 'REFLOW-02' in the equipment system, and simply 'oven No. 2' in shop-floor conversation. Second, causal relationships are often implicit. Parameters are coupled, and a temperature change may pass through two or three operations before it shows up as a defect. Third, versions change frequently. After a parameter adjustment, it is often unclear whether older data is still valid.

This means that if you import raw data from each system directly into a graph database, the result is usually not knowledge but a tangle of contradictory nodes. The value of a graph depends on trustworthy relationships, and that is precisely the property raw data lacks most.

A Common Pitfall: Extracting First, Defining Later

The most frequent mistake is to start with automatic extraction. A team gathers a large volume of documents and uses a model to batch-extract entities and relations. It looks fast, but the outcome is usually a mess of entity types. 'Temperature', 'oven temperature', and 'process temperature' become three separate nodes, and relation labels are left unconstrained. By the time business users try to query the graph, they discover that the results cannot be aligned.

Another common mistake is aiming for a single graph covering the entire plant. The larger the scope, the harder it is for experts to take part and the higher the cost of validation. The graph quickly reaches a state where no one dares to use it. A third mistake is treating the graph as a one-time project that stops being updated after delivery, even though manufacturing processes keep changing.

What Works: Narrow the Scope, Then Define the Ontology

A more reliable sequence is to first select one or two product lines and one typical defect type, keeping the scope small enough that a few process engineers can genuinely review it. Then, together with process experts, define the ontology (schema): decide which entity types the graph will contain and which relationships are allowed.

A workable starter ontology usually includes operations, equipment, process parameters, materials, defect types, standard clauses, and corrective actions. Relationships can be limited to a small set, such as 'operation includes parameter', 'parameter affects defect', 'defect occurs at equipment', and 'disposition follows standard'. The fewer relationship types you have, the easier they are to validate and the less likely semantic drift becomes. Once the ontology is settled, automatic extraction with a model can be considered, with the constraint that all extraction results must fit within this framework.

Data Alignment and Expert Validation: Where Trust Comes From

Extraction is only the first step. Alignment and validation determine whether the graph is usable. Alignment resolves naming: build an alias table that maps 'reflow soldering', 'REFLOW-02', and 'oven No. 2' to a single operation node. This table is itself a high-value process asset and should be maintained by process engineers.

Validation requires rules combined with manual spot checks. For example, require every 'parameter affects defect' relationship to carry at least one source record, such as a process trial report, a quality inspection record, or an equipment log. Relationships without a source should be marked as pending verification. In addition, each relationship should carry a version number and an effective date. When process parameters change, older relationships should be marked as historical rather than deleted outright.

If you want to put this 'ontology plus validation' workflow into practice, you can bring extraction rules, alias mappings, and expert review into one workflow on Duaer (https://www.duaer.com), which makes it easier to track the source and status of each relationship. Still, the workflow is only a carrier. The quality of the graph must ultimately be tested against your own data and your experts' judgment.

For the earlier step of checking whether your data is structured enough to be used, you can first refer to the approach in Data AI Readiness Assessment to see which data sources are ready to use and which need cleaning first.

How to Tell Whether a Process Graph Is Good

Do not measure success by node counts or total relationship counts, since those numbers are easy to inflate. More meaningful indicators include coverage, meaning the share of key parameters for the target defect types that have been loaded into the graph; credibility, meaning the proportion of randomly sampled relationships that experts confirm as correct, with relationships that have sources and those without sources counted separately; usability, meaning whether typical questions from process staff can be answered by following a complete path in the graph; and reuse, meaning how often new lines and new employees query the graph.

These metrics should be baselined early in the project and re-measured in every iteration cycle. If credibility stays low over time, the cause is usually a flawed ontology design rather than a model that is not strong enough.

One Thing You Can Do This Week

Pick the defect that causes your team the most trouble, such as a particular type of weld failure or a dimension out of tolerance. Use a single table to list the operations linked to that defect, up to five key parameters, the equipment involved, the existing source documents, and the responsible person. Then ask a process engineer to test whether the table can answer twenty real questions. This exercise requires no system at all, yet it quickly exposes the largest gaps in the ontology design.

The value of a process knowledge graph lies not in how big it is, but in making a small set of critical knowledge queryable, verifiable, and sustainable. Get one chain of logic working thoroughly first, and only then think about expansion.

If your team is preparing to launch a process knowledge graph project, you are welcome to sign up for a trial at https://www.duaer.com and run one real defect chain through the workflow first.

If you would like us to first map out your scenario, tell us your production line type and the problem you most want to solve, and we will reply with a written implementation roadmap.

https://api.duaer.com/form/1fea7709-3f8a-47f7-b4e3-eb5fb90e3213

Questions

What data do I need to prepare before building a process knowledge graph?

You will usually need to review data sources such as route cards, equipment operation and alarm logs, and quality defect records, then determine which sources can be used directly and which need cleaning first. You should also collect the different names used across systems for the same operation or equipment and build an alias table to prepare for later alignment.

Does a process knowledge graph have to cover the entire plant?

No. A more reliable approach is to start with one or two product lines and one typical defect type, keeping the scope small enough for process engineers to review in practice. The larger the scope, the harder it is for experts to participate, the higher the validation cost, and the more likely the graph is to end up unused.

How can I tell whether a process knowledge graph is well built?

Avoid measuring it by node counts or total relationship counts. Focus instead on coverage, credibility, usability, and reuse. Credibility should be assessed through expert sampling, with relationships that have sources and those without sources counted separately. Set baselines early in the project and re-measure them in every iteration cycle.